Tipo de motor DC Tensão de alimentação: 12VCC Rotações nominais do motor: 6900rot./min Temperatura de trabalho: -40...60°C Dimensões: Ø24.2 x 30.5mm Tensão de tyrabalho: 8.5...15.5VCC
O Funduino Mega 2560 é uma placa electrónica baseada no microcontrolador ATmega2560. Tem 54 entradas/saídas digitais (dos quais 14 podem utilizar-se para saídas PWM), 16 entradas analógicas, 4 portas UART, uma ligação USB para programação e alimentação, um conector de alimentação, um conector ICSP e um botão de reínicio. A placa funciona a 16 MHz e tem tudo o que é necessário para desenvolver projectos com microcontroladores. Basta liga a um computador com um cabo USB para começar. O Funduino Mega 2560 R3 é compatível com a maioría de expansores ShieldO Funduino MEGA 2560 tem as mesmas prestações e características que o Arduino MEGA 2560 R3 Caracteristias:- Microcontrolador - ATmega2560 - Voltagem de alimentação - 5V - Voltagem de entrada (recomendada) 7-12V - Voltagem de entrada (limites) - 6-20V - Pinos digitais I/O - 54 (dos quais 14 podem ser saídas PWM) - Pinos de entrada analógica - 16 - Corrente contínua por pino I/O - 40 mA - Corrente contínua para o pino: 3.3V - 50 mA Memória Flash - 256 KB (Dos quais 4 KB podem ser utilizados pelo bootloader - RAM - 8 KB - EPROM - 4 KB
1 Using photosensitive resistance sensor sensitive type 2 Working Voltage:3.5V-5V 3 Output form:Digital Switch show (0 and 1) 4 Fixed Bolt Hole,easy installation 5 Small PCB size:3.2CM*1.7CM 6 the comparator output, signal clean, good waveform, driving ability is strong, for more than 15 ma 7 with adjustable potentiometer to adjust light brightness
One, the I2C input, PWM output control 16 road, steering gear can use 16 road Second, the steering gear power independent V + input maximum 6 V Three, logic signals and logical power independent output for 3 to 5 v Fourth, 40-1000 hz frequency Five, the number of channels: 16 channel Six, resolution: 12 bit
Low power consumption Power supply for 2 ~ 5.5V DC Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation
High performance-price ratio Small volume, easily embeded to other products Strong function with support LWIP protocol, Freertos Supporting three modes: AP, STA, and AP+STA Supporting Lua program, easily to develop.
1: FET module, the input and output are completely isolated. 2: Signal trigger terminal: digital high and low level. Can be connected to the microcontroller IO port, PLC interface, DC power supply, etc. 3: Input signal voltage: 3V~24V current: about 5ma. 4: The output can control high-power equipment, motors, bulbs, LED strips, DC motors, micro pumps, solenoid valves, etc. 5: Output controlled voltage: 5V~36V. Current: less than 5A, more than 5A need to add heat sink, the maximum can not exceed 20A. 6: Using the original F5305S power FET, you can input PWM, control motor speed, brightness of the lamp, etc.
Temperatura de funcionamento: -15 to 70° c Pressão: 80 to 106 kPa Alimentação: DC Tipo de Display: Digital Only DIY Supplies: Electrical Escala de medição: DC 0-100V 0-10A
DiDisplay construction 128*64 DOTS Display mode TN/STN Display type Positive Transflective Backlight LED, 5.0V Viewing direction 6 o´clock Operating temperature Indoor Driving voltage Single power Driving method 1/33 duty,1/6 bias Type COB (Chip On Board) Number of data line 8-bit parallel Connector Pin / ZEBRA Key Parameters Driver IC ST7920 / ST7921 Interface Parallel / SPI Backlight Blue Character Color White Character Set ASCII Dimension 93 * 70 * 13.5
Classe D Corrente: 20mA Tensão de funcionamento: DC7.5 V-15 V Potência nominal de saída: 10w + 10w (8ohm) Frequência de Resposta: 20 Hz a 50 KHz Alimentação recomendada: 12V, o PIN central de 12VDC é "+
GPS Module NEO-6M Model: GY-GPS6MV2 Input Supply Voltage Range: 3.3V-6V, on board voltage regulator maintains 3.3V I/O Maximum Logic Level: 3.6V WAAS (Wide Area Augmentation System) enabled GPS unit. 27 seconds to first fix (TTFF) for cold starts On board LED will blink after module acquires a position fix and will continue blinking as long as the module has a fix 50 Channel NEMA GPS receiver UART: 9600 baud by default, but is configurable from 4800 to 115200 baud 5Hz max update rate External EEPROM for configuration storage Four plated mounting holes, 3mm in diameter One additional non-plated mounting/antenna cable hole, 4mm in diameter Position Accuracy: 2 m and better with multiple good satellite signals Velocity Accuracy: 0.1 m/s Maximum Velocity: 500 m/s Heading Accuracy: 0.5 degrees while moving On board battery for battery backed RAM (BBR). Battery is recharged through a simple diode and resistor charger circuit from the on board voltage regulator´s 3.3V output Ceramic antenna -156dBm Hotstart sensitivity Weight: 17.6g (0.6oz) Dimensions of GPS Module: 36mm (1.42in) x 25.8mm (1.02in) x 4mm (0.16in) Dimensions of Antenna: 25.5mm (1in) x 25.5mm (1in) x 8.8mm (0.35in) Compatible with various flight control modules that provide GPS computer test software Compatible with UART capable devices including Arduino, Raspberry Pi, MSP430, and MSP432. Interface: RS232 TTL
Admite cartão micro SD Alimentação: 4.5V ~ 5.5V, (placa de circuito del regulador de voltaje 3.3V) Interface de comunicação: SPI standard Dimensões: 4.1 x 2.4cm
